This thread is dedicated to connect you with Red Hat subject matter experts who can help answer your questions regarding Red Hat remote exams. Please see the following resources for Red Hat Remote Exams below:
For questions on scheduling or redeeming your exams, please use the Red Hat Certification team comment form here.
**Our subject matters experts in the Red Hat Learning Community will not be assisting with tasks related to scheduling exams.
Hello everyone -
I just scheduled the remote RHCSA exam. Reading the confirmation email, I notice though that we are not allowed to use a wireless connection during the exam. I do not have a wired connection at home. I use my mobile phone as a hotspot and the mobile network connection is reliable and fast (I've been using it to work from home since the beginning of the pandemic without any issues). This mobile network succcessfully passed the Compatibility Test.
This is what the email says:
Network Connection: Unless it is physically not possible, a wired network connection should be used, not wireless, to ensure the most reliable delivery of your exam.
Did I get it right? Can you kindly confirm?
I have an employee Lenovo P1 laptop running the RHEL CSB. The cameras and all microphones work fine, built in and external.
When booting from the ISO (old or one linked in email), none of the microphones work (I'm in settings adjusting the gain, etc.). There is a key on the keyboard to disable the microphone, however it's not lit up and does nothing when booted from the ISO.
I checked the bios to see if there was anything there that might cause the microphones to be turned off and didn't find anything. I tried various mechanisms to get the microphones to work like pressing the MIC key on the keyboard etc.
I tried another laptop I have and the microphones did work, but the NIC did not (which I expected as the NIC is not well supported in Linux.) I have to try a couple of other laptops, however, since my work laptop doesn't seem to work, I figured others might have the same issue, or there may be a work around, thus I bring it to your attention.
I was scheduled to take the RHCSA exam remotely this morning on my laptop, however, due to odd technical difficulties I was unable to take my exam. My issue was my proctor could not see my screen, they said I was not sharing my screen and on their end it was 'blank'. They also said the connection was slow. After being instructed to restart my laptop, reinitialize the Red Hat Exam environment, and complete the compatibility test four times, the proctor still couldn't see my screen. Everything checked out ok on my end--Successful compatibility test and the little icon at the top of my screen showed that I was sharing my screen, microphone, and camera with the proctor (plus, I had been doing the compatibility tests on my laptop weeks and days before my exam with no issue). 30 minutes had passed into my exam time so I had to reschedule. Now I am concerned this will happen again and I don't know how to resolve this before I have to reschedule. :(
Has anyone else tried to take an exam remotely and had this issue of the proctor not being able to see your screen?
As a backup I am trying to verify that I can set up the test environment on my desktop computer, but so far the test environment loads to 100%, and then the screen goes blank and stays that way until I do a hard reboot to get out of the live boot (I've tried two versions of this live boot that were mentioned in this forum--one from 8-2020 and the other from the "Getting Ready for Your Remote Exam" pdf, but still no success with either).
I hope someone can provide me with some solutions. Testing is already stressful, but to have proctoring issues on the day of the test is the worst!
IIRC, One of the compatibility tests (media check tests) displays the streams available to the proctor. Were you able to view the desktop feeds in this test? If yes, and the proctor could still sees the bank screen, its best to work with the live support team and try sorting it out.
@Vishal , thanks for the reply.
Yes, I was able to view the desktop feeds, but my proctor still saw a blank screen. I was also speaking with live tech support by phone while this issue was going on but they offered no solution aside from rescheduling.
I did some troubleshooting on my own and I think my upload speed on my home network is still not fast enough for the exam. Even though I was passing the compatibility test, my upload speed was only .75mbps so I think that's why the proctor was not seeing my screen--upload speed wasn't fast enough.
I know it is not recommended, but I'm going to have to use my LTE/4G network as a hotspot for the remote exam instead of my home network. My home network speed is 6mbps download and .75mbps upload, but my LTE network speed is 28mbps download and 17mbps upload which a LOT better than my home network.
My 2 cents.
LTE/4G network has a latency and packet drops. You might not get smooth exam experience. Mouse lagging or trailing letters like 'wwwwwork' . I faced this when I used mobile network.
I appreciate your 2 cents @Sarang! I'll keep this in mind. If I can't find a workaround I may have to deal with it.
Probably you can use LTE router with cable.
You can try TP-Link MR400 AC1200 Wireless Dual Band 4G LTE Router, or like as it.